We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
137 questions answered by our experts.
Sort by:
- < Prev
- 1
- 2
- 3
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kim
February 11, 2020
What causes water not to come into the machine? The sensor light is on but nothing is happening.Thanks
For model number MVWX655DW1
Hello Kim, thank you for your question. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the wash may fill slowly or not fill at all. The water inlet valve requires sufficient water pressure to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.I hope this helps.
20 people found this helpful.
Was this helpful?
Thank you for voting!
Paul
November 30, 2019
Clothes come out wet, does not spin all of the water out of the clothes. Maytag bravos top load washing machine.
For model number MVWX655DW1
Hello Paul and thanks for writing.Sounds like you need to replace the drive belt Part Number: PS11747978 is in the list of compatible items for your model. We hope this helps. Please contact us anytime.
15 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Felisa
December 22, 2019
It is only 2yr old. When I start it the motor is running but the basket is not spinning and all the lights are off. So I unplug it to avoid overheating the motor. What could be the problem?
For model number MVWX655DW1
Hello Felisa, Thank you for the question. This could be a defective Control Board, PartSelect Number PS12114298. Electronic control board manages the washer's functions such as filling, washing, draining and spinning. Hope this helps!
14 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Electronic Control Board
$442.85
In Stock
David
January 30, 2020
How to remove coins caught in the slot/gap in the basin.
For model number MVWX655DW1
Hello David, Thank you for the question. You may need to remove the Washplate PartSelect Number PS11769534 to get access to remove the Basket and coins. We hope this helps!
10 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Ray
March 17, 2020
My washer doesn’t cycle out of wash cycle
For model number MVWX655DW1
Hello, Thank you for your question. You will want to check into the timer itself, that could be faulty and not allowing it to advance. We hope this helps.
6 people found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- 2
- 3
- Next >
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch ... Read more and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Read less
Parts Used:
-
Jerry from WALLA WALLA, WA
-
Difficulty Level:
Really Easy
-
Total Repair Time:
15 - 30 mins
-
Tools:
Nutdriver, Screw drivers, Socket set
84 of 114 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hub had warn its grooved teeth off and washer wouldnt agitate
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned ... Read more it back up and got caught up on laundry. good day when the washer is fixed.
Read less
Parts Used:
-
Allison from RICHFORD, NY
-
Difficulty Level:
Easy
-
Total Repair Time:
15 - 30 mins
-
Tools:
Screw drivers
45 of 58 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noise, grinding sounds. Wash tub stopped turning but motor and cycles kept functioning. Process of elimination, must be the clutch assembly.
Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.
Parts Used:
-
David from BLOOMINGTON, IN
-
Difficulty Level:
Easy
-
Total Repair Time:
30 - 60 mins
-
Tools:
Screw drivers, Socket set
39 of 49 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
