How to reset a Maytag Bravos XL washer?

Disconnect the Power. Disconnecting the washer's electricity for three minutes is the simplest way to reset a Maytag washing machine. When the power is cut off, the washing machine's electrical charge can dissipate, allowing it to reset. If the reset doesn't work, unplug the washer once more, this time for ten minutes.

How do you put a washing machine in diagnostic mode?

First, press the spin and soil level buttons at the same time, followed by the power button . It's a bit like pressing Control, Alt, Delete. You should hear the buzzer twice to indicate success. From them, you just have to press the start button repeatedly to cycle through the modes.

My MVWX655DW0 Model Overview from PartSelect.com (2024)

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

30 questions answered by our experts.

Sort by:

< Prev
1
2
3
Next >

Search filter:

Clear Filter

Your search term must have 3 or more characters.

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!

Lisa

July 7, 2021

My drum and agitator spin in opposite directions and make a loud grinding noise. Do you know what is causing this?

For model number MVWX655DW0

Hello Lisa, Thank you for the question. We suggest checking the Washer Drive Pulley for wear or damage. We hope this helps!

3 people found this helpful.

Was this helpful?

Thank you for voting!

Related Parts:

Washer Drive Pulley

$54.33

In Stock

Don

January 7, 2020

I have replaced these parts in this order.Gear clutchhubwasher plateshift actuator.i have run a diagnostic multiple times and the code that comes up is f7 e0meaning that it displays the f rinse spin done, e nothing.i am at a loss

For model number MVWX655DW0

Hello Don, thank you for your question. The Washer F7E0 error code means the main board has lost power or the voltage being supplied is too low. If you have reset the unit, and replaced the above mentioned parts, the most likely issue is the main board which is PartSelect Number: PS10062118. I hope this helps!

Tim

January 11, 2024

Lid locks then it spins real fast one time then goes to a lid lock light flashing never fills up with water.

For model number MVWX655DW0

Hello Tim, thank you for getting in touch. We have concluded that the issue is with the control board, part number PS10062118. You may need to replace it to fix the issue. We hope this solves your problem!

1 person found this helpful.

Was this helpful?

Thank you for voting!

Related Parts:

CNTRL-ELEC

$223.69

In Stock

< Prev
1
2
3
Next >

Defective lid latch - Cabrio Washer

The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform ... Read more ation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.

Read less

Parts Used:

Lid Latch Assembly

William from Wakefield, RI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

93 of 112 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Noise on bottom of Washer louder as time went on. 1 1/2 years

Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch ... Read more and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.

Read less

Parts Used:

Drive Belt Washer Drive Pulley

Jerry from WALLA WALLA, WA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set

84 of 114 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Hub had warn its grooved teeth off and washer wouldnt agitate

ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned ... Read more it back up and got caught up on laundry. good day when the washer is fixed.

Read less

Parts Used:

Drive Hub Kit

Allison from RICHFORD, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

45 of 58 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My MVWX655DW0 Model Overview from PartSelect.com (2024)

FAQs

My MVWX655DW0 Model Overview from PartSelect.com? ›